扭剪型電動扭矩扳手操作注意事項、扭剪型電動扭矩扳手許多用戶可能并不陌生,但對于新聯系人扭剪型電動扭矩扳手的用戶,可能不理解扭剪型電動扭矩扳手操作注意事項,在這種情況下,如果操作不當,可能引起扭剪型電動扭矩扳手是否損壞,以下用戶不明白,我們一起學習。
Many users may not be unfamiliar with the operation precautions of the torsional shear type electric torque wrench, but for the users of the torsional shear type electric torque wrench who are new contacts, they may not understand the operation precautions of the torsional shear type electric torque wrench. In this case, if the operation is improper, it may cause damage to the torsional shear type electric torque wrench. The following users do not understand, We study together.
扭剪式電動力矩扳手使用注意事項
Precautions for the use of electric torque wrench
1. 接通電源前，應檢查電源電壓是否與貨物銘牌相符，有無接地裝置。當電源電壓超過+10%時，應采取調壓措施控制精度。地面好沒什么區別。
1. Before connecting the power supply, check whether the power supply voltage is consistent with the cargo nameplate and whether there is grounding device. When the power supply voltage exceeds + 10%, voltage regulation measures shall be taken to control the accuracy. Good ground makes no difference.
2. 機器的操作條件為-10℃-40℃，過高或過低均會導致掌握精度下降。
2. The operating condition of the machine is - 10 ℃ - 40 ℃, too high or too low will lead to the decrease of the mastering accuracy.
4. 當機器用于裝配螺母時，扭矩不應大于附加扭矩值。正常情況下，沒有手柄擰緊或生銹的螺母，沒有適合使用的手柄總成，以免形成機器保護。
4. When the machine is used to assemble nuts, the torque shall not be greater than the additional torque value. Under normal circumstances, there is no nut with handle tightened or rusted, and there is no handle assembly suitable for use, so as to avoid machine protection.
5、當改變轉動位置時，電機建議停止轉動后才能停止轉動，嚴禁在運行中打開正反轉開關。
5. When the rotating position is changed, the motor can only stop rotating after it stops rotating. It is strictly prohibited to turn on the forward and reverse switches during operation.
6、當手柄主動停止時可抓住開關等待4-5秒后手柄啟動，否則手柄無法啟動。
6. When the handle stops actively, hold the switch and wait for 4-5 seconds before the handle starts, otherwise the handle cannot start.
