扭剪扳手檢驗及保養
Inspection and maintenance of torsional shear wrench
1、電動扳手的金屬外殼應可靠接地，其外殼應有定期檢驗試驗合格證，并在期限內。
1. The metal shell of the electric wrench shall be reliably grounded, and its shell shall be provided with regular inspection and test certificate within the time limit.
2、檢查電動扳手機身安裝螺釘緊固情況，若發現螺釘松了，應立即重新扭緊，否則會導致電動扳手故障。
2. Check the fastening of the mounting screws on the body of the electric wrench. If the screws are found to be loose, tighten them again immediately, otherwise the electric wrench will fail.
3、檢查手持電動扳手兩側手柄完好，不開裂可破損，安裝牢固。
3. Check that the handles on both sides of the hand-held electric wrench are intact, not cracked or damaged, and installed firmly.
1、確認現場所接電源與電動扳手銘牌是否相符。是否接有漏電保護器。
1. Confirm whether the on-site power supply is consistent with the nameplate of the electric wrench. Whether leakage protector is connected.
2、根據螺帽大小選擇匹配的套筒，并妥善安裝。
2. Select the matching sleeve according to the size of the nut and install it properly.
3、在送電前確認電動扳手上開關斷開狀態，否則插頭插入電源插座時電動扳手將出其不意地立刻轉動，從而可能招致人員傷害危險。
3. Before power transmission, confirm that the switch on the electric wrench is disconnected, otherwise when the plug is inserted into the power socket, the electric wrench will turn unexpectedly immediately, which may cause personal injury.
4、若作業場所在遠離電源的地點，需延伸線纜時，應使用容量足夠，安裝合格的延伸線纜。延伸線纜如通過人行過道應高架或做好防止線纜被突出損壞的措施。
4. If the workplace is far away from the power supply and it is necessary to extend the cable, use the extension cable with sufficient capacity and install the qualified extension cable. If the extension cable passes through the pedestrian aisle, it shall be elevated or measures shall be taken to prevent the cable from being crushed and damaged.
5、盡可能在使用時找好反向力距支靠點，以防反作用力傷人。
5. Try to find the supporting point of the reverse force distance during use to prevent the reaction force from hurting people.
6、使用時發現電動機碳火花異常時，應立即停止工作，進行檢查處理，排除故障。此外碳刷一定要保持清潔干凈。
6. In case of abnormal carbon spark of the motor during use, stop working immediately, check and deal with it and eliminate the fault. In addition, the carbon brush must be kept clean.
7、站在梯子上工作或高處作業應做好高處墜落措施，梯子應有地面人員扶持。
7. Measures for falling from height shall be taken when working on a ladder or working at heights, and the ladder shall be supported by ground personnel.
The above is about the price of torsional shear wrench http://www.lvhe888.com I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service
