1、使用范圍：漢普電動扭剪扳手可更換內外套筒，可用于從M12到M30的扭剪型螺栓的施工作業。

1. Scope of use: The Hanpu electric torsion shear wrench can replace the inner and outer sleeves and can be used for the construction of torsion shear bolts from M12 to M30.

開關操作：

Switch operation:

開動工具時，扣動開關柄即可，停止時松開。

When starting the tool, simply press the switch handle and release it when stopped.

注：接通工具電源插頭之前，一定要檢查確認開關工作是否正常，松開時能回到“關”的位置上。

Note: Before connecting the power plug of the tool, it is necessary to check and confirm whether the switch is working properly. When released, it can return to the "off" position.

緊固操作方法：

Tightening operation method:

1、將工具內套筒對正螺栓的梅花頭，使梅花頭插入內套筒，并完全蓋住梅花頭。

1. Align the inner sleeve of the tool with the plum blossom head of the bolt, insert the plum blossom head into the inner sleeve, and completely cover the plum blossom head.

注：將套筒對準螺栓梅花頭時要小心，撞擊梅花頭時會使其損壞。以致不能正常插入套筒。

Note: Be careful when aligning the sleeve with the bolt's plum blossom head, as hitting the plum blossom head may damage it. So that it cannot be inserted into the sleeve properly.

2、對工具向前用力，使其向前滑動，直到外套筒完全蓋住螺母為止。如果工具不能完全蓋住螺母，請輕微的左右轉動同時向前用力。

2. Apply force to the tool forward and slide it forward until the outer sleeve completely covers the nut. If the tool cannot fully cover the nut, please turn it slightly left and right while applying force forward.

3、扣動電動扳手開關，外套筒將旋轉，開始擰緊螺母。當達到設定的例句力矩時，螺栓梅花頭將在有V型口處被剪斷。螺栓梅花頭將留在內套筒里。

3. Turn on the electric wrench switch, the outer sleeve will rotate, and start tightening the nut. When the set torque is reached, the bolt plum blossom head will be cut at the V-shaped opening. The bolt plum blossom head will remain in the inner sleeve.

4、松動開關，沿著垂直方向撤下工具?！?/p>

4. Loosen the switch and remove the tool vertically‘

5、扣下推頂器扳機，竟螺栓梅花頭從工具中頂出，拿好

5. Pulling off the trigger of the pusher, the bolt's plum blossom head was pushed out of the tool, and it was taken out